our products

D&Q Mining is a high-tech company integrating R&D, production and sales. It provides mature products and solutions such as crushers, sand making, milling equipment, mobile crushing stations, etc., for aggregate, mining and waste recycling.

is a tattoo liner set to a dime gap or nickel

How to Tune a Tattoo Machine to Work

The general rule of thumb for starting position is dime gap for liner and nickel gap for shader. This means that the gap of the front spring to the contact screw point (while you are holding down the armature bar to create the gap) should be the width of a nickel for shading and the width of the dime

More

Dime / Nickel Tuning Teach Me To Tattoo

The old school trick of the trade was the dime gap liner nickel gap shader. Take the armature bar assembly and press down on the armature bar’s nipple (the spot where the needle bar’s loop attaches to the grommet and then to the armature bar) and press down on it until the bottom of the armature bar hits the top of the front coil (the

More

How to Adjust Your Tattoo Machine for Shading & Lining eHow

Aug 30, 2017· One or two tattoo guns (two preferred) Liner needle ("3 round" recommended for beginners) dime. nickel. magnifying glass or jeweler's loupe. A tattoo artist stencils an image before beginning the line work. Set the gap for line work by turning the contact screw until the gap between the tip of the screw and the front spring of the

More

Step-by-Step Tips for Tattoo Power Supply Connection

May 10, 2012· Liner with a dime width gap and your shader with a nickel width gap. Trust me I asked these same questions and I even doubted the information. Most cases it wont be your power supply that is the problem it will be how your machine is tuned.

More

Nickel or Dime??? Help Me Tattoo Training Forum

Sep 16, 2012· General Tattoo Chat. Beginners Tattoo Questions Answered. Machines, Equipment & Setup . Nickel or Dime??? . Nickel or Dime??? Starter tays; Start date 6 Jul 2012; T. tays. Basic. Joined 28 Jun 2012 Messages 2 First Name dean

More

Step-by-Step Tips for Tattoo Power Supply Connection

Mar 17, 2020· Liner with a dime width gap and your shader with a nickel width gap. Trust me I asked these same questions and I even doubted the information. Most cases it wont be your power supply that is the problem it will be how your machine is tuned.

More

Machine Tuning Tattooing Basics Tattoo Magic

Mar 12, 2021· The nickel and dime trick means that if you can just fit a nickel in that space then you're good for lining, and a dime if good for shading. This is not always the case. I believe this image is from the A to Z guide to Tattooing from Spaulding.

More

Tattooing The Right Way: SETTINGS FOR THE TATTOO MACHINE

Mar 01, 2009· There is some practical knowledge that should be leaned about the tattoo machine before attempting to do repairs. The gap between the contact point and the contact screw (for the shading machine), should be about the width of a nickel. For the liner, the gap should be about the width of a dime.

More

How to Tune a Tattoo Machine (Liner & Shader) YouTube

Mar 13, 2013· The nickel and dime method of tuning tattoo machines. Shader nickel, liner dime!

More

How to Tune a Tattoo Machine (Liner & Shader)

Sep 30, 2013 The nickel and dime method of tuning tattoo machines. Shader nickel, liner dime!

More

How do you set up a tattoo machine as a liner? Answers

Set the contact point gap at about a nickel's width for shading, a dime's width for lining. Run the tattoo machine for shading slightly slower. Don't go bigger than a five mag for beginners.

More

How to adjust your tattoo machine for shading & lining

Jul 14, 2020· Set the gap between the armature bar and the contact screw for shading to approximately 2mm, or the thickness of a U.S. nickel. Attach a needle tube appropriate for shading to the tattoo gun. Insert the matching needle bar into the tube and secure it.

More

Setting up a Liner Tattoo Machine / Gun

Setting up a Liner Tattoo Machine / Gun Liner:Setup for accuracy, speed and definition. This setup is for outlining tattoos. A liner machine is characterized by shorter front spring for a shorter stroke. Smaller gap between front spring and contact screw contact point. Generally runs faster than a shader. Setting up Liner: Hold down the armature against

More

Difference Between Tattoo Guns??? Liner and or Shader

Jan 04, 2013· But the main way to tell is how its setup. The contact screw should sit over the grommet for shader or over front edge of the metal bobbin on the front coil for a liner. the airgap when the arm bar is down should be about dime for a liner & nickel for shader. Also spring gauge, capacitor resistance & arm bar weight come into it.

More

Lining: Long stroke or short stroke scratcherstattooforum

Jun 13, 2014· no need to add to much gap to ride the tip of the needle in my own opinion. for the larger needle groupings I use my Paco Rollins. I have that one set up with a larger stroke and using a 47uf cap and a thicker main spring to be able to push those needles in. so far that is what I found that works best for me (so far of course)

More

How to Tune or setup of a tattoo machine for lining

This video shows you how to setup a tattoo machine to do lining and shading. Make sure the armature bar and front spring has about a 4mm gap. Once that is on, set it to about a 30-degree angle. Next with the contact spring you need to set the armature bar and the tool should be set to about 2mm. A good way to check this is with a dime. Now as long as the tattooing machine runs and sounds

More

How to Set Up a Tattoo Machine for the First Time

Feb 16, 2021· In other words, you can't tattoo well if you haven't mastered the basic mechanics of your machine. In this tutorial, I will tell you how to set it up correctly and illustrate the instructions with pics of a tattoo liner I use. If you have any questions about setting up your liner

More